Questions? Get Online Help
Call 1-800-447-7367 or 231-946-3712,
Monday-Friday 8AM-5PM EST.


			
			
			
			
			
			
 
Thumbnail
Crobalt Solid Round Bit 5/16"x2" L
Title
Crobalt Solid Round Bit 5/16"x2" L
Description

These Crobalt tips are ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit. This size is appropriate for the users of the new ML8mm Diamond Toolholders, designed for the small bench top lathes, such as the Unimat, Atlas 6", Sherline, and other new Asian lathes.

Crobalt cast alloy is an alternative tool bit to the HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium, there is no iron or steel in the alloy.

Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 1/4" square.

They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.

The lathe is a 1960s Colchester Chipmaster.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$16.00
Availability
In Stock
Order Code
BC268
Thumbnail
Crobalt Square Bit 1/4"x1-1/2" L
Title
Crobalt Square Bit 1/4"x1-1/2" L
Description

Crobalt cast alloy is an alternative tool bit to the 1/4" HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium, there is no iron or steel in the alloy.

Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 1/4" square.

They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.

The lathe is a 1960s Colchester Chipmaster.

The Crobalt tips are 1/4" x 1/4" x 1 1/2" (6.35mm x 6.35mm x 38mm) and they come with square cut ends to be ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$14.00
Availability
Backordered
Order Code
BC207
Thumbnail
Crobalt Square Bit 3/16"x1-1/2" L
Title
Crobalt Square Bit 3/16"x1-1/2" L
Description

Crobalt cast alloy is an alternative tool bit to the 3/16" HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium. There is no iron or steel in the alloy.

Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 3/16" square.

They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.

The Crobalt tips come with square cut ends to be ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit. This particular size is specifically chosen to work on the ML8 Diamond Toolholder, both Right-hand and Left-hand models.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$14.00
Availability
In Stock
Order Code
BC227
Thumbnail
Crobalt Square Bit 5/16"x1-1/2" L
Title
Crobalt Square Bit 5/16"x1-1/2" L
Description

Crobalt cast alloy is an alternative tool bit to the 5/16" HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium. There is no iron or steel in the alloy.

Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 5/16" square.

They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.

The lathe is a 1960s Colchester Chipmaster.

The Crobalt tips come with square cut ends to be ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit. This particular size is specifically chosen to work on the ML8 Diamond Toolholder, both Right-hand and Left-hand models.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$16.00
Availability
Backordered
Order Code
BC259
Thumbnail
Drilling, Reaming, Tapping and Milling on the Drill Press DVD
Title
Drilling, Reaming, Tapping and Milling on the Drill Press DVD
Description

by Rudy Kouhoupt

Drilling, Reaming, Tapping and Milling on the Drill Press. Many people sell the drill press short when it comes to machining. Rudy demonstrates many operations that make it a very important part of your shop.

Watch a brief clip from the DVD.

 
Price
$35.95
Availability
In Stock
Order Code
BC74
Thumbnail
Figure It Out - Common Sense and a Calculator DVD
Title
Figure It Out - Common Sense and a Calculator DVD
Description

by Rudy Kouhoupt

Did you ever wonder how high the valves should lift; what happens when you scale it up or down; how big the inlet passage should be; why small engines run so fast; how heavy it will be; how the flywheel effect changes with size; how to set your lathe for greater accuracy; or how to check tapers and angles? Rudy describes and illustrates his real world approach to problem solving on these and other subjects in the shop and at the drawing board. He includes an outline and drawings of examples used in the DVD presentation.

Watch a brief clip from the DVD.

 
Price
$35.95
Availability
Backordered
Order Code
BC75
Thumbnail
Flux Core Arc Welding DVD
Title
Flux Core Arc Welding DVD
Description

by Steve Bleile

This DVD is an introduction to flux core arc welding, featuring extremely close-up demonstrations of actual welds in all positions. Steve discusses equipment, welding wires, fundamentals, self-shielded and gas shielded types. 56 minutes.

 
Price
$25.95
Availability
Backordered
Order Code
BC83
Thumbnail
FoR 12mm Parting Tool
Title
FoR 12mm Parting Tool
Description

The FoR Inverted Parting Toolholder operates with the blade held in an upside down position and can be used on front or rear tool posts.

For lathes with a screw on chuck the holder must be used with a rear tool post.

Parting blade not included.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$105.00
Availability
Backordered
Order Code
BC270
Thumbnail
FoR 12mm Parting Tool Combo
Title
FoR 12mm Parting Tool Combo
Description

FoR (Front or Rear) Inverted Parting Toolholder includes a fine, high-strength Crobalt parting tool. Operates with blade held upside down. Use in front or rear tool post. Model specifically set for tool posts on 12mm Diamond Toolholder.

  • Inverted blade design significantly reduces chance of jam-up and blade breakage
  • Minimal side overhang and no front overhang help maximize rigidity
  • Cutting takes place on underside. Swarf tends to fall out of groove rather than pile up on top of cutting edge
  • Lack of swarf on top of blade means coolant is free to get right in to cutting edge
  • Horizontal mounting of blade further reduces chance of blade pulling itself into cut and is especially advantageous when turning brass and bronze.
  • Simple to resharpen--only front face has to be ground.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$160.00
Availability
Backordered
Order Code
BC234PKG
Thumbnail
FoR 16mm Parting Tool
Title
FoR 16mm Parting Tool
Description

The FoR Inverted Parting Toolholder operates with the blade held in an upside down position and can be used on front or rear tool posts.

For lathes with a screw on chuck the holder must be used with a rear tool post.

Parting blade not included.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$105.00
Availability
In Stock
Order Code
BC271
Thumbnail
FoR 16mm Parting Tool Combo
Title
FoR 16mm Parting Tool Combo
Description

FoR (Front or Rear) Inverted Parting Toolholder includes a fine, high-strength Crobalt parting tool. Operates with blade held upside down. Use in front or rear tool post. Model specifically set for tool posts on 16mm Diamond Toolholder.

  • Inverted blade design significantly reduces chance of jam-up and blade breakage
  • Minimal side overhang and no front overhang help maximize rigidity
  • Cutting takes place on underside. Swarf tends to fall out of groove rather than pile up on top of cutting edge
  • Lack of swarf on top of blade means coolant is free to get right in to cutting edge
  • Horizontal mounting of blade further reduces chance of blade pulling itself into cut and is especially advantageous when turning brass and bronze.
  • Simple to resharpen--only front face has to be ground.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$160.00
Availability
In Stock
Order Code
BC272PKG
Thumbnail
FoR 20mm Parting Tool
Title
FoR 20mm Parting Tool
Description

The FoR Inverted Parting Toolholder operates with the blade held in an upside down position and can be used on front or rear tool posts.

For lathes with a screw on chuck the holder must be used with a rear tool post.

Parting blade not included.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$105.00
Availability
In Stock
Order Code
BC284
Thumbnail
FoR 20mm Parting Tool Combo
Title
FoR 20mm Parting Tool Combo
Description

FoR (Front or Rear) Inverted Parting Toolholder includes a fine, high-strength Crobalt parting tool. Operates with blade held upside down. Use in front or rear tool post. Model specifically set for tool posts on 20mm Diamond Toolholder.

  • Inverted blade design significantly reduces chance of jam-up and blade breakage
  • Minimal side overhang and no front overhang help maximize rigidity
  • Cutting takes place on underside. Swarf tends to fall out of groove rather than pile up on top of cutting edge
  • Lack of swarf on top of blade means coolant is free to get right in to cutting edge
  • Horizontal mounting of blade further reduces chance of blade pulling itself into cut and is especially advantageous when turning brass and bronze.
  • Simple to resharpen--only front face has to be ground.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$160.00
Availability
In Stock
Order Code
BC285PKG
Thumbnail
FoR 8mm Parting Tool
Title
FoR 8mm Parting Tool
Description

The FoR Inverted Parting Toolholder operates with the blade held in an upside down position and can be used on front or rear tool posts.

For lathes with a screw on chuck the holder must be used with a rear tool post.

Parting blade not included.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$95.00
Availability
In Stock
Order Code
BC230
Thumbnail
FoR 8mm Parting Tool Combo
Title
FoR 8mm Parting Tool Combo
Description

FoR (Front or Rear) Inverted Parting Toolholder includes a fine, high-strength Crobalt parting tool. Operates with blade held upside down. Use in front or rear tool post. Model specifically set for tool posts on 8mm Diamond Toolholder.

  • Inverted blade design significantly reduces chance of jam-up and blade breakage
  • Minimal side overhang and no front overhang help maximize rigidity
  • Cutting takes place on underside. Swarf tends to fall out of groove rather than pile up on top of cutting edge
  • Lack of swarf on top of blade means coolant is free to get right in to cutting edge
  • Horizontal mounting of blade further reduces chance of blade pulling itself into cut and is especially advantageous when turning brass and bronze.
  • Simple to resharpen--only front face has to be ground.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$150.00
Availability
In Stock
Order Code
BC236PKG
Thumbnail
FoR 9.5mm Parting Tool
Title
FoR 9.5mm Parting Tool
Description

The FoR Inverted Parting Toolholder operates with the blade held in an upside down position and can be used on front or rear tool posts.

For lathes with a screw on chuck the holder must be used with a rear tool post.

Parting blade not included.

Features/Tips

If backordered, shipping may take 2 to 3 weeks.

 
Price
$95.00
Availability
In Stock
Order Code
BC269