Machinist's Resources « Metalworking « Storefront

Questions? Get Online Help
Call 1-800-447-7367 or 231-946-3712,
Monday-Friday 8AM-5PM EST.

Filter Results

Basic Maintenance for the Vintage South Bend Lathe

If you are thinking about cleaning up and using that old South Bend Lathe that you inherited from your grandfather (the one that has been sitting in your garage for the last 20 years), this collection of maintenance tips will help you get that beautiful piece of iron back into service. "Basic Maintenance for the Vintage South Bend Lathe" is a starting "how-to" guide for keeping all vintage South Bend Lathes in good working order. The information is applicable to all models ranging from the 9" workshop series to the industrial versions which went from a 10" swing all the way up to 16". The manual will help educate new machine operators and enthusiasts on the correct procedures to set up, clean, lubricate, and adjust all of the critical features of the lathe. The manual is 70 pages, fully illustrated with many B&W photographs and diagrams plus step-by-step instructions on the proper methods for keeping the machine in good working order.
Softbound. 70 pages.

$16.95

In Stock

BMVSBL

Build the Snow -- A Tandem, Double-Acting Engine

By Doug Kelley

Doug Kelley's very popular Snow natural gas pumping engine, as an internal combustion engine construction series, first appeared in The Home Shop Machinist magazine. An ample supply of back issues in which the project appeared soon sold out -- encouraging reprint in a booklet format. The resulting 44-page plus cover saddle stitch volume includes 13 pages of photos that showcase full-size Snow engines housed in museum settings around the U.S. -- some that run and some that are being restored with the intent to run.

$14.95

In Stock

SNOW

Building a Heat-Treating Furnace DVD

By John Benjamin

John Benjamin has been building firearms for many years. Some of the nation's most successful benchrest rifle barrels have been built by him. Part of his secret is the fantastic heat-treating furnace he built. He shows and describes how it is built, and how it is used.
Barrels are heated in a vertical position, and gently brought to a stage of stillness evenly throughout their entire length. His furnace has been used over 300 times without any evidence of wear. A bill of materials is included. 45 minutes.

$25.95

In Stock

BC87

Crobalt Cutoff Blade for FoR Parting Tool

FoR holder takes common 1/2" x 3/32" tapered type parting blade. Beveled top and bottom to lock securely into a holder.
The FoR Parting Tool Holder does not include a blade in the purchase, but these are widely available from several manufacturers and many suppliers worldwide. The blade is easily sharpened on any bench grinder and instructions for setting up, sharpening, and tips for best results, are included with the holder.
Blades are double bevel for use in Brown and Sharpe type holders. Can be used in either a right or left hand holder.
Features/Tips
If backordered, shipping may take 2 to 3 weeks.

$70.00

In Stock

BC210

Crobalt Solid Round Bit 3/16"x1-1/2" L

These Crobalt tips are 3/16" x 1-1/2" with round ends to be ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit. This size is appropriate for the users of the new ML8mm Diamond Toolholders, designed for the small bench top lathes, such as the Unimat, Atlas 6", Sherline, and other new Asian lathes.
Crobalt cast alloy is an alternative tool bit to the HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium, there is no iron or steel in the alloy.
Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 1/4" square.
They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.
The lathe is a 1960s Colchester Chipmaster.
Features/Tips
If backordered, shipping may take 2 to 3 weeks.

$14.00

In Stock

BC239

Crobalt Solid Round Bit 5/16"x2" L

These Crobalt tips are ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit. This size is appropriate for the users of the new ML8mm Diamond Toolholders, designed for the small bench top lathes, such as the Unimat, Atlas 6", Sherline, and other new Asian lathes.
Crobalt cast alloy is an alternative tool bit to the HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium, there is no iron or steel in the alloy.
Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 1/4" square.
They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.
The lathe is a 1960s Colchester Chipmaster.
Features/Tips
If backordered, shipping may take 2 to 3 weeks.

$16.00

In Stock

BC268

Crobalt Square Bit 3/16"x1-1/2" L

Crobalt cast alloy is an alternative tool bit to the 3/16" HSS tips usually used in the Diamond Tool Holders, its ideal for turning tough materials such as stainless, cast iron, and high carbon steels. Tougher and less brittle than carbide it can be ground using a normal aluminum oxide wheel, Crobalt contains 50% cobalt with the remainder being tungsten and chromium. There is no iron or steel in the alloy.
Watch the Diamond Toolholder in action doing a comparison test between M42 HSS (CoHSS) and Crobalt cast alloy -- both toolbits are 3/16" square.
They are being used in a Right Hand 12mm model Diamond Tool Holder, to turn 304 and 316 stainless bar and an interrupted cut on a piece of cast iron.
The Crobalt tips come with square cut ends to be ground to the correct angle by the customer, using the Diamond Tool Holder grinding jig that comes with each tool holder kit. This particular size is specifically chosen to work on the ML8 Diamond Toolholder, both Right-hand and Left-hand models.
Features/Tips
If backordered, shipping may take 2 to 3 weeks.

$14.00

In Stock

BC227

Figure It Out - Common Sense and a Calculator DVD

By Rudy Kouhoupt

Did you ever wonder how high the valves should lift; what happens when you scale it up or down; how big the inlet passage should be; why small engines run so fast; how heavy it will be; how the flywheel effect changes with size; how to set your lathe for greater accuracy; or how to check tapers and angles? Rudy describes and illustrates his real world approach to problem solving on these and other subjects in the shop and at the drawing board. He includes an outline and drawings of examples used in the DVD presentation.
Watch a brief clip from the DVD.

$35.95

In Stock

BC75

** US Pricing. Foreign pricing applied during checkout process.

VP

Storefront

Metalworking

Machinist's Resources

VP Storefront One-Stop shopping for all VP publications